Six_speed_demon
Well-Known Member
I did this!
Official 'What did you do to your car today?' Thread
- Thread starter Dar-Dar
- Start date
- Thread starter
- #3,203
Six_speed_demon
Well-Known Member
Wrapping the Downpipe might slightly dampen it a first but once it's heated no... Once my waste gate open I'm pretty much running open exhaust so that's going to be loud anyway. And the turbo blanket is going help it spool a tad faster because the hot side is staying hot
Six_speed_demon
Well-Known Member
Nail on head! But by insulating it and keeping the heat in the header and or Downpipe it will speed up the air flow as well but I have wrap ever header I've ever owned and my bay temps would drop over 120* for sure
Nevtec
Well-Known Member
I got some primer on my Eco beast
Six_speed_demon
Well-Known Member
Well I guess this qualifies!
Tomorrow just have to put the waste gate Downpipe do the boost controller put the dump pipe on and then the drain and bam the transplant will be done! Couldn't have done none of this without my right hand man Ryan! Thanks again buddy! Your the freaking best! Will be firing up tomorrow!
Tomorrow just have to put the waste gate Downpipe do the boost controller put the dump pipe on and then the drain and bam the transplant will be done! Couldn't have done none of this without my right hand man Ryan! Thanks again buddy! Your the freaking best! Will be firing up tomorrow!
- Thread starter
- #3,211
Dar-Dar
Mordorator
- 19,329
- 9,900
- Vehicle Model
- Civic Si
- Body Style
- Fiji Blue Pearl Coupe Coolest Member Since: May 15, 2011
My oil catch can was leaking. I thought the drain plug was the culprit, but the actual bottom piece threads on to the body. So I wrapped Teflon on the threads. No more leaks!
I also installed injected OE front and top mount.
I also installed injected OE front and top mount.
njhustler
Well-Known Member
I installed my Hawk HPS brake pads today.
07TLX
Well-Known Member
Not really a one day thing.... But let's see, in the last month, replaced the water pump, alternator, belt tensioner and harmonic balancer and put a serpentine belt from a dx on a lx because my a/c compressor is going bad and I don't want to spend the money on it....
njhustler
Well-Known Member
Sounds like youve been a busy person. I guess you bypassed the ac pulley?. Feels a bit peppier doesnt it?.
njhustler
Well-Known Member
Yesterday , I installed my Full Race catback. A few quick notes , the rubber hangers are a pita , seriously bad. I used wd40 and all but they were still really hard to move. Next comes the wtf were they thinking with the connection for the axle back?. A good old flange is no good anymore?. It wasnt easy to get it lined up to tighten it. I was on my back by myself , car on stands. Lastly , does it get any quieter as it breaks in?. Ive seen many videos and none of them seemed this loud. Is there anyway to quiet the exhaust down a bit?. I knew the noise was going to be an issue but it was the next mod to do as we dont really have that many options for more power aside from forced induction. Also , my best 1/4 mile time is 14.4 @96mph. What do you think I could shave off of that time with the catback and a retune?. More than 1-2 tenths?. One more thing does it look like the exhaust is a bit to far to the left?
- Staff
- #3,216
I will assume you didn't read my DIY thread?
If you had, I made note that grease is better for the hangers than WD40.
Give it about 500 miles or so to break in and it will get quieter.
Mine sits a bit to the left as well.
njhustler
Well-Known Member
I did , awhile ago. I didnt have it and was too anxious to install to go get some plus it was getting late / dark. I hope so. I got in about 150 miles today , its ok on the highway but city acceleration is too loud.
07TLX
Well-Known Member
It's a little bit better, I am just glad I got it done... Tail of the dragon is right around the corner
- Staff
- #3,219
- 25,544
- 10,598
