i will add pictures later BUT you really dont need pics, but here you go
what you need from hondapartsdeals.com:
image
1) a navi (duh, if its an si make sure its a premium audio system navi)
2) gps antenna (39835-SNA-A01)
3) 2 #10 (93913-14420)
4) 8 #8 (91551-SE0-003) (4 for each side)
5) 1 # 7 (91507-SL9-003)
thats for that picture, next is from this picture:
image
6) 1 #12 (77250-SNA-A01ZA)
7) 1 #13 (77255-SNA-A00)
8) 1 #14 (77256-SNA-A00)
9) for numbers 35, 36, and 27 re-use from the stock radio
ok now that you got all of that begins the install (again pics will be added later):
theres two ways of doing this install...the easy way and the harder way.
lets do the easy way (since i did do it this way)
ok buy pigtails for this, what are pigtails? they are the harness plugs that plug into the back of the navi. you only need 12p/22p:
image
17p is the same as HARNESS A (you WILL use from your stock radio)
ok now that you got the pigtails, lets first do the easy one the 17p plug:
here's the pin out for the pigtail....
image
image
image
tap (from the navi pigtail) 1 to A17
tap 4 to A9
now next to the B HARNESS/22P, luckily for us the one on the left is from the navi pigtail and the one on the right is from the stock radio.
image
this is a pic of the two harness you need. it goes from the green one to the stock one under it
image
the following pics show the taping from one wire to the other wire
image
image
image
connect B1 to B3
connect B2 to B4
connect B3 to B5
connect B6 to B6
connect B7 to B7
connect B11 to B13
connect B12 to B14
connect B13 to B15
connect B15 to B <----there is no ground for the B HARNESS, so i tapped this one into A9 from above
conncet B20 to B16<-----is not on the diagram but this is your amp
the gps antenna is easy...just unscrew 3 screws from your speedometer lift it on the right side and you will see a place to put it, plug in your cables and fire it up, make sure you got the 4 digit radio code.
image
image
***this is up to you how you want to tap... there are plenty of ways to "tap" the way i did it was i stripped each wire about 2 cm then poked a hole then from the navi pigtail i went in the hole and twist it around...then i soldered it and covered it with electric tape.****
also the hard way to do this is no pigtails...just find some wires then solder TO THE NAVI then the other end tap it into the stock harness...i say harder because who would want to solder to tha navi?
got questions? just shoot away....
sites i used:
DIY - Installing an OEM Nav into a Non-Nav CRV - HondaSUV Forums - Discussion forum and bulletin board for Honda CR-V, CRV, Element, Pilot, HR-V owners
Help, CRV stereo pinout? where's the Ignition sense? - HondaSUV Forums - Discussion forum and bulletin board for Honda CR-V, CRV, Element, Pilot, HR-V owners
http://www.8thcivic.com/forums/attachment.php?attachmentid=8891&d=1193346656
this is information collected from a one month period. i hope you guys can benefit from this, i know i did!
more random pics:
image
image
image
image
image
image