- Thread starter
- Staff
- #121
Yup....morimoto 5k
New Year, New ride... 13' Fit!
- Thread starter Nomar06
- Start date
- Status
Yup....morimoto 5k
- Thread starter
- Staff
- #122
Got the angel eye set in place. Had to trim the projectors a little bit so they could fit inside the angel eyes.
Need to find a "constant on" fuse that I can tap into so the angel eyes will stay on when the car is on since I have to remove the stock DRL fuse to make the bi-xenon HID work properly.
Other than that, the whole retro is pretty much go to go into the headlights. I am hoping I don't have to trim the shrouds.
Need to find a "constant on" fuse that I can tap into so the angel eyes will stay on when the car is on since I have to remove the stock DRL fuse to make the bi-xenon HID work properly.
Other than that, the whole retro is pretty much go to go into the headlights. I am hoping I don't have to trim the shrouds.
- Staff
- #123
- 52,105
- 22,314
what'd you use to hold the stuff together...jbweld?
- Thread starter
- Staff
- #124
Yup...
- Thread starter
- Staff
- #125
It's time!!!
- Staff
- #126
- 52,105
- 22,314
without going back through this thread - if you haven't done the horn upgrade (can't remember)... perfect timing now
- Staff
- #127
- Thread starter
- Staff
- #128
The main horn is already done. You can see it there in the middle. The alarm beep just got done now. Although not sure how it will sound. I just use the left over hi-low horn upgrade from the '13 accord I had.
Nix
Jötunn Moderator
nice work dude!
PS I hate you. You're too fast!
PS I hate you. You're too fast!
- Staff
- #130
- Thread starter
- Staff
- #131
Well, just like anything I mods I do to my car......I have an issue.
The panamera shrouds are too wide and too deep so I need to trim them down some. Nothing horrible but I don't have much room to work with do to the LED rings. I also need to bring the projector forward even after trimming down the shroud.
Looks like my happy arse is riding his bike to Home Depot in the morning to try to find some rubber type spacers. Similar to what the projectors came with.
The panamera shrouds are too wide and too deep so I need to trim them down some. Nothing horrible but I don't have much room to work with do to the LED rings. I also need to bring the projector forward even after trimming down the shroud.
Looks like my happy arse is riding his bike to Home Depot in the morning to try to find some rubber type spacers. Similar to what the projectors came with.
- Staff
- #132
- 52,105
- 22,314
sucks man. Try the plumbing section. You may be able to use something like a rubber gasket from a tub/sink drain, or stack some rubber gaskets from a toilet tank (if that's not too wide)?
- Thread starter
- Staff
- #133
I was thinking the same......Im sure I will find something.
- Thread starter
- Staff
- #134
Had to sacrifice part of the led ring to get everything to properly work. I'll explain in another post but both headlights are sealed back up and everything will be buttoned up tomorrow.- Staff
- #135
- 52,105
- 22,314
Looks good from what I see. You obviously had luck at Home Depot?
- Thread starter
- Staff
- #136
I did but then that created issues with the bulb not properly seating in the projector.
Nix
Jötunn Moderator
I can't wait to see how they look lit up.
- Thread starter
- Staff
- #138
- Staff
- #139
- 52,105
- 22,314
looks really good man. Did you end up pulling your drl fuse? Morimoto bulbs?
- Thread starter
- Staff
- #140
Pulled the DRL fuse and Morimoto bulbs, 5k temp.
- Status