- Staff
- #81
- 56,739
- 24,147
You'll need him to do a retune for the car to actually be functional.
DIY RBC Swap into 9th Gen - * ECU Tuning Is Mandatory *
- Thread starter Privman
- Start date
You'll need him to do a retune for the car to actually be functional.
OgAk907
Member
- 5
- 0
Right now I'm turning with VitViper but still have the idle sound. He say it might be my vacuum leak or my tb adjustment but I check that already. Any clue why it's still idle?
- Staff
- #83
- 56,739
- 24,147
Is the rpm bouncing? I don't know how far you are into tuning, or what map you're on? Has vit said the problem isn't tuning related at this point?
OgAk907
Member
- 5
- 0
Yes,my rpm keep bouncing from 1 to 2rpm and I'm on map 2 only with VitViper. Don't wanna drive around with my idle problem.
- Staff
- #85
- 56,739
- 24,147
vitviper is going to be your answer for that. If he's saying it's not tune related and you have a vacuum leak.... I don't know what else to say. He diagnoses cars nonstop
Gonna get going on this. Hope some of y'all will be around just in case. Lol. But seriously.
Have you looked through this thread?
http://9thcivic.com/forum/threads/rbc-zdx-prl-install-tips-and-discussion.9076/
Gilles LeClair
Well-Known Member
Have any of you guys ever seen a RBC intake manifold that had the coolant section cut off? (picture below)
Gilles LeClair
Well-Known Member
The coolant part on the far right of the manifold where it bolts up to the head has been cut off.
Ktuned makes a coolant plate that kinda replaced it (second picture)
Ktuned makes a coolant plate that kinda replaced it (second picture)
Last edited:
Gilles LeClair
Well-Known Member
I have the black rbc manifold that I posted at first, missing everything else to complete the swap.
I've been told that it would run cooler intake air temperatures.
The PRL adapter kit is not needed but I do need a thermal gasket instead.
What I am wondering is which thermal intake manifold gasket am I going to need.
I'm not sure if the ktuned coolant plate goes over a thermal gasket or if I need a thermal gasket that only goes over the rbc manifold.
I've been told that it would run cooler intake air temperatures.
The PRL adapter kit is not needed but I do need a thermal gasket instead.
What I am wondering is which thermal intake manifold gasket am I going to need.
I'm not sure if the ktuned coolant plate goes over a thermal gasket or if I need a thermal gasket that only goes over the rbc manifold.
The thermal gasket would go between the manifold and the engine, so I don't think it would affect that coolant plate area at all.
Not sure which one you would need because it sounds to me like you already have the RBC made to match since you don't need the adapter kit.
http://www.powerrevracing.com/2012-Civic-Si-RBC-RRC-Intake-Manifold-Gasket-p/p168.htm
http://www.powerrevracing.com/2012-Honda-Civic-Si-Thermal-Intake-Manifold-Gasket-p/p161-02.htm
Not sure which one you would need because it sounds to me like you already have the RBC made to match since you don't need the adapter kit.
http://www.powerrevracing.com/2012-Civic-Si-RBC-RRC-Intake-Manifold-Gasket-p/p168.htm
http://www.powerrevracing.com/2012-Honda-Civic-Si-Thermal-Intake-Manifold-Gasket-p/p161-02.htm
Gilles LeClair
Well-Known Member
Found out today that i'll have to use a thermal gasket from a k20a2 which is a rsx since they also don't have the coolant portion.
I wasn't sure if the coolant plate would need a thermal gasket but it simply goes directly on the block.
I will also need a throttle body spacer if I remember correctly? Would it be a spacer from the 2006-2011 civic si?
I wasn't sure if the coolant plate would need a thermal gasket but it simply goes directly on the block.
I will also need a throttle body spacer if I remember correctly? Would it be a spacer from the 2006-2011 civic si?
Gilles LeClair
Well-Known Member
This the adapter kit i'm assuming?